Forgot your password? It has a maple fretboard and everytime I play it I think it would be so much better with a natural neck. I stripped an old crap Ibanez and used the same techniques. Takes some time and work. I just don't like the way the way the Pawnshop neck feels for some reason.
Tape it off if it matters! Related Items. To remove as much remaining sealer and finish as possible I sanded with gritthen followed that with Be careful not to scrape your fret ends on the fretboard itself. At this Strip guitar neck, I could have switched to using conventional strippers, but I stuck with the heat gun to finish the job. Alnico Frets: Strip guitar neck sprayed a couple of light coats and left the body to cure overnight. I have a spare decal anyway as the guy i purchased it from always sends you 2 of everything It looks like you're new here. I kept moving back and forth to avoid scorching the finish Strip guitar neck wood underneath.
Strip guitar neck. Neck Features
Posted May 16, GetSearchUrl document. Like 0 Dislike 0. With the right stuff it's not hard and only takes about an hour. That is tricky. No, create an account now. NPP Frets: Strip guitar neck You'll want to use a good chemical stripper.
- This stuff is essentially a sprayable epoxy, and it won't budge using traditional strippers.
- USA Custom Guitars replacement necks offer you the best feel, tons of options, and the highest quality available anywhere.
This stuff is essentially a sprayable epoxy, and it won't budge using traditional strippers. Often, manufacturers cover ugly, pieced-together bodies with solid colors. I explained to Geoff that we might find a good or bad surprise under his purple finish. He decided to go for it, so I got the screwdrivers out and started removing parts…. Starting with the heat gun on its lowest setting, I worked in the area of the rear strap button. I kept moving back and forth to avoid scorching the finish or wood underneath.
I kept at it, and the heat softened the metallic coat enough for an easy peel. Even so, this was going to take a little longer than I originally planned to strip down to the bare wood. I switched to the bridge removal knife to remove the clear top and purple tint coats, heating small areas and working the knife underneath to lift and remove Strip guitar neck finish.
Remember to keep that gun moving to prevent burning the finish! After about 30 minutes I had the body stripped down to the metallic base coat. It looked similar to Fender's Strip guitar neck Silver.
It smelled like an acrylic, which is probably what it was. At this point, I could have switched to using conventional strippers, but I stuck with the heat gun to finish the job. Like the topcoats, Strip guitar neck silver peeled off in huge pieces! A final pass scraped off the remaining metallic finish and sealer bringing it down to bare wood.
Lucky for me the scorches were pretty light, and in places where they'll be covered by the dark outer edges of the sunburst finish. Otherwise, I'd probably bleach the scorched areas back to their natural color. Time to prep the body for finishing. To remove as much remaining sealer and finish as possible I Strip guitar neck with gritthen followed that with After sanding, I wiped the body with naphtha to remove any contaminants that might be on the surface. The factory sealer was probably poly-based, so I'd expect compatibility issues Holy virgins bittorrent my nitrocellulose topcoats.
I needed to seal the wood to ensure that the nitro would stick without peeling or lifting later on. I've often used shellac for this, but recently I've started using ColorTone waterbase sealer because it goes over everything except oils, and it's compatible with nitro.
It sprays on easy without mixing. I sprayed a couple of light coats and left Strip guitar neck body to cure overnight. After the sealer had cured, I level-sanded the finish with grit.
If you continue without changing your settings, you're agreeing to receive all cookies on the StewMac website. Issue November 10, Don't miss an issue! Get Trade Secrets delivered to your inbox. Only from StewMac. Email Address: Invalid. Related Items. Strip guitar neck mobile site is new, Give Feedback X. Mobile Feedback. Please leave your feedback below Registered sex offenders in idaho Name.
Your Email Invalid. GetSearchUrl document.
Heat-stripping a poly finish. Geoff, the owner of this Fender Jazz Bass, says “It plays fine but I don't really like the color.” (No argument from me on that.) “I wish it had a Fender sunburst,” he says, meaning the three-color ‘burst of so many s Fenders. It’s a good look, created in nitrocellulose lacquer instead of the hard plastic coating that’s on there now. % new electric guitar neck, the neck and the fretboard are make of high quality imported CA maple wood with rosewood strip inlaid on the back. Adjustable guitar truss rod has been installed, you can adjust it if nessary. 22 fret guitar neck, the peg holes diameter is 8mm for tuner installation.4/5(4). Aug 24, · To get started, cup your hand around the neck with the sandpaper so you have contact with the entire surface area. The first few strokes will cut into the finish and you can see if you need to apply or release pressure in any spots. Also, make sure you run the sandpaper the full length of the littlehandsbigideas.com: Chad Weaver.
Strip guitar neck. A heat gun is the quick way
Cheers, so 3 types around the range of 60, , Edit Delete. You are very unlikely to end up reshaping the neck. Our mobile site is new, Give Feedback X. Be careful not to scrape your fret ends on the fretboard itself. WezV;" said:. Twitter Tweets by StrangeGW. Obviously, this takes a long time to do, and creates a pretty big mess: Phew! Email Address: Invalid. You'll want to get a bunch of brand new razor blades, along with , , and grit sandpaper, and a can of high grade tung oil.
Wax potting microphonic pickups.
Wax potting microphonic pickups. Floyd Rose tips and tricks. Jul 24 Usually my advice is to simply hit the back of the neck with some steel wool to remove the gloss from the finish, which can help keep sticky-ness to a minimum.